HP G60 No Power- Blinking Power LED

 HP G60 - No Power, Will not turn on, Will not charge



This unit arrives with No Power Problem.  When plugging in the AC Adapter I notice that the Power LED is (steady) blinking. The Power button does not work and does not light the charge light, so I can diagnose this as a major POWER IN problem. 


Inspecting the power section behind the DC Jack and the bottom side of the board.  Turning the board over, I notice a section burnt and a cap missing. 


So- the first thing I do is remove the caps indicated as 1,2 ,3 in pictures.
Then do a quick test- plug the power adapter back into the unit.



The power LED no longer blinks.  Cleaning up the area shows me that the cap indicated by #3 had severely shorted and the frayed metal end was also shorting the #1 cap. Removing the solder from the pad, and the welded metal from the missing cap, I have a working surface area to replace the parts. These are standard ceramic caps that can be found on an old board and nothing unique about them.




After cleaning and replacing all the caps in image, time for a final test. Voila!
The unit fires up, and because of the failure, or the unit sitting too long, the BIOS setting were lost or changed because I did not have the unit totally assembled, and peripherals were missing.  That is minor and when totally assembled the unit functions normally.










Solution: replace blown and shorted caps.
The cost is so insignificant that all 3 were replaced, rather than doing one at a time, which takes longer.

Comments

  1. froggstylerTue Jan 31, 01:16:00 PM EST

    any solution for v3000 won't on....

    ReplyDelete
  2. HoosierTue Jan 31, 01:29:00 PM EST

    Kind of vague description- what can I surmise from that?

    ReplyDelete
  3. ThinkingbullMon Mar 12, 03:50:00 PM EDT

    great description of this fault/fix on an hp-g60 many thx

    ReplyDelete
  4. UnknownSat Jul 28, 04:23:00 PM EDT

    hi i have a g60 its turn on go in bios but dint recognize any hard drive or DVD drive i tried bios resting by bios battery and from inside bios but dint work u have any idea that how to resolve this issue plz help me

    ReplyDelete

Post a Comment

I cannot repair laptops for you via the internet, I can only answer questions related to posts. This is because I have not had experience on every motherboard that is out there. Bear with me.

If you do need it repaired. Contact me for quote (US/CDN Only)

Popular posts from this blog

Important parts on DV6000 and DV9000 series

Image
These are important parts if you are looking for shorts or opens on the DV series. This image shows the location of the FDS6679. A common cause of shorts in the DV series. When the power supply is plugged into the laptop and it shorts out/turns off it's usually caused by this MOSFET being shorted.  Plainly stated. You plug the adapter into the DC Jack and the Blue Ring fails to light up, and the Power Supply shuts off. Giving no power to the tip. To reset adapter, unplug from AC (mains) and wait 15-30 sec. Then plug in again. The adapter is not damaged, since this is how it is protected. These parts do not determine charge time or per centage. The FDS6679 only closes to complete Positive circuit.  The AO4407 only closes when the battery is plugged in. As a test- Check the voltage of the Drain side (pins 5-8) with AC adapter and no battery - you should see 0 volts.  When you contect the battery you should have 10-14v depending on DV6000 or DV9000 series. IF the AO4407 is open
Read more

Dell Inspiron 1501 - Dead, No Power, Won't Charge

Image
Picture 1 This is a common problem with the Dell Inspiron 1501/E1705/6000 series. Most of the motherboards use the same general layout and design. You can tell by the white and silver cases used. From my guess, the solder on the leads of FL1 [filter] tend to lose contact after regular use. Perhaps eating away at the Filters pad, due to the current it is carrying. Sometimes it may be years before it finally lose contact, other times only months pass. In this instance the laptop was a couple of years old before it failed. How to fix it: Picture 2 Remove FL1 Clean contact area Replace FL1 Solder back onto clean surfaces. Click picture to see larger image Picture 2 Shows another failed NO Charge issue. FL1 cannot handel the surge when plugged in and eventually arcs then lose contact with the solder pad.  In this case if you cannot find a replacement, you can simply turn the coil [FL1] upside-down, and make sure you have positive voltage on  the circuit.  Try to t
Read more

Tips on Testing MOSFETs

Image
Imagine the flow direction Source to Drain This is how I test FETS  What I will try to do here is to provide a little insight on how to test  MOSFET's in circuit the easiest way I can think of. Essentially the FET acts as a switch, and the GATE either opens or closes the switch. When power is supplied to Pin 4 (usually the GATE) it will either open or close depending on the type of MOSFET it is. The arrows shows the direction for reference when using a meter to test.   Setting the meter in DIODE mode. On the N-Channel FET place the NEG lead on Pin 6/7 and the POS lead on Pin 2/3. You should get a reading of some value ~100 to 500 or higher. Imagine the flow direction Drain to Source On the P-Channel FET place the POS lead on Pin 6/7 and the NEG lead on Pin 2/3. Again you should get a reading of some value ~100 to 500 or higher. The reason I say pins 2/3 and 6/7 is because they are common,
Read more